Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Paradise Homeowners
If a gate stops closing on its own, drags on the ground, or won’t latch all the way, the problem is almost never the whole gate. It’s usually one hinge, one post, one weld, or one sensor. We fix the part that failed instead of selling you a new gate, and we weld on site in Paradise so the gate never leaves your driveway. Our technicians have up to 25 years of experience. Behind that work stands the 90-Day Done Right Promise, stamped in writing on every job, plus a 10% discount for seniors and veterans. Call (888) 292-7536 and estimates are free.
Key Takeaways:
- We repair the gate instead of replacing it, and weld on site in Paradise.
- Live person answers the phone around the clock, including the worst hour of a bad night.
- The price is agreed before any work starts, and it doesn’t change at the door.
- Every job carries the 90-Day Done Right Promise in writing.
What Our Gate Repair Service Includes
Electric Gate Repair
An electric gate that stops mid-swing, reverses without touching anything, or hums and does nothing is the most common call we get in Paradise. We test the control board, the wiring, and the safety sensors before we touch anything else, because a board that reads fine can hide a bad connection two feet away. If it turns out to be a failed board or a motor winding, we tell you plainly and show you what failed, rather than guessing at parts.

Automatic Gate Repair
Automatic gates fail in the operator’s logic, the limit switches, or the safety loops, and the symptom usually points at the wrong one. A gate that closes on a car one morning and works fine the next is a textbook sign of a failing loop or a limit switch that’s drifted. We run the operator through its full cycle and watch the limit settings, then reset them so the gate stops where it should every time.

Hinge & Post Repair
A gate sags in the hinge post, not in the middle, and that’s where we start. Worn hinges allow the whole leaf to drop a half inch, which drags the bottom edge on the concrete and misaligns the latch and the opener all at once. We re-weld the hinge to sound steel and reset the post if the footing has shifted, because fixing the panel without the post means you’ll be fixing it again.

Gate Realignment
A gate that’s out of square binds against the post, wears out hinges early, and eventually burns up the operator trying to force it shut. A lot of alignment problems trace back to a swollen wooden frame from our summer heat or a concrete footing that’s settled over the years. We square the gate and set the hinges so it swings free and closes on its weight, with no motor doing the work the hinges should be doing.
Lock Repair
Locks jam from rust, misalignment, or a worn latch that no longer catches fully, and a gate that won’t lock is a gate you can’t trust at night. We repair or replace the latch and strike plate, then adjust the gate so the latch meets the plate square. Electronic locks and access keypads fall in this category too, and we handle the wiring side.
Weld & Rust Repair
Paradise gates take a beating from dry heat, wind-blown grit, and monsoon dust, and steel rusts where water pools in a low joint. A cracked weld is usually a weld that never penetrated the base metal to begin with, which is a common problem with cheap installs. We grind out the old weld, clean the steel to bare metal, and lay a proper full-penetration weld right there in your driveway.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair
We service LiftMaster gate operators and know their control boards and limit switches inside and out, which matters when a board fails and the replacement takes a week. We also work on DoorKing systems, whose logic boards and intercom wiring are a common source of “it works for me, not for you” problems. Whether the parts come off LiftMaster or DoorKing, the repair approach is the same: test the components in order and fix the one that failed.
We also handle Mighty Mule and Elite equipment, plus FAAC, BFT, Linear, Viking, and Ghost Controls. A Mighty Mule operator that won’t reverse on command is usually a limit switch, not the board, and an Elite slide gate that stalls can be a worn roller rather than the motor. If your gate is any other make, we can still take a look. Whether you have LiftMaster or any other brand, we can help.
Signs You Need Gate Repair Right Now
- The gate drags or scrapes the ground. That’s a hinge or post failure, and every cycle you run it makes the drag worse. Waiting just wears the hinge pin and the operator faster.
- The opener reverses without touching anything. A safety sensor or loop is failing, and it can close on a car or a person. Stop using the automatic function until someone tests it.
- The gate won’t latch or lock at night. Latch misalignment and worn strike plates are quick fixes, and a gate that won’t lock is a security gap you don’t want to leave open.
- You see rust streaks, cracked paint, or a visible weld crack. Water gets in and the crack spreads. A cracked weld on a post or hinge is a structural warning, not cosmetic.
- The gate hums, buzzes, or trips the breaker. That points to a motor winding or wiring fault, and continuing to power it can damage the board. Shut the circuit off and get it checked.
Our Gate Repair Process – Step by Step
- 1
We listen first. When did it start, what changed, and what does it do right before it fails? That conversation usually narrows the problem to one system before we open the toolbox. We ask about the gate’s history too, because a repair after a bad install needs a different conversation than a repair after ten quiet years.
- 2
We test the whole cycle. We run the operator, watch the limit points, check the safety sensors, and put a level and a square on the hinge posts. Watching a gate close on its own tells us where it’s actually failing, not just where it sounds like it’s failing.
- 3
We give you a written, itemized price before touching a thing. Parts, labor, welding, and what’s not included. If it’s a two-part repair, you see both prices and you decide whether to do both now or just the urgent one.
- 4
We repair on site. Welding, hinge replacement, realignment, and operator repair happen in your driveway. Nothing gets hauled off to a shop where it sits for two weeks.
- 5
We test it, then walk you through it. We run the gate ten times, check the lock, and make sure the safety reverse works. Then you get the 90-Day Done Right Promise in writing. If it acts up inside that window, one call brings us back.
How Much Does Gate Repair Cost in Paradise?
Gate repair in Paradise typically runs $150 to $650, depending on what failed and whether welding is involved. A straightforward hinge adjustment or latch repair usually lands in the $150 to $250 range. A hinge and post re-weld with realignment is typically $300 to $500. An electric or automatic operator repair with a board swap commonly falls between $350 and $650, and a full motor or operator replacement can run higher.
Several factors move the price: the gate material, whether the footing has shifted, whether the wiring is buried or exposed, and whether you have a swing or slide gate. Slide gate repairs often cost more because the track and rollers add parts. We don’t believe in hourly surprise bills, so the price you agree to before work starts is the price you pay.
How to avoid overpaying: get a written estimate, ask whether the part is being repaired or replaced, and ask if the price includes site welding. A cheap quote that leaves out welding or post work will cost double later. Every estimate from us is free, with a free second opinion on any written estimate you already have. Seniors and veterans get a permanent 10% discount, and there’s $40 off any repair over $200. No trip charge inside the county.
See the difference
Before
After
Before
After
Before
AfterGate Repair Near Paradise – Our Service Area
We cover Paradise and the surrounding communities, including Winchester, Whitney, Spring Valley, Enterprise, Henderson, Sunrise Manor, Summerlin, Las Vegas, North Las Vegas, Boulder City, and Sandy Valley. Response times depend on the day, but we prioritize gates that are stuck open, won’t lock, or pose a safety risk. For drivers and walkers across the valley, our page on Gate Repair in Winchester shows what we can do in that community, and our home page gives you the full picture of what we offer.
Serving Paradise, NV – Our Local Coverage Area
We serve Paradise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Paradise
Gate repair means fixing the specific component that failed instead of replacing the whole gate. That can be a hinge, a post weld, a latch, a control board, a limit switch, a sensor loop, or a motor winding. We diagnose first, price it in writing, and repair on site. If the gate only needs a new hinge and a realignment, that’s the job you get.
Most common repairs are done in a single visit of one to two hours. A hinge swap or latch adjustment can take under an hour once we’re on site. A post re-weld, realignment, or operator board replacement often takes two to three hours because of the welding and testing. If it’s a bigger job, we tell you upfront so you can plan around it.
Most repairs fall between $150 and $650, with adjustments and latches at the low end and operator or motor work at the high end. The price is quoted and agreed before work starts, so you won’t see a bigger invoice than the estimate. Seniors and veterans get 10% off, and there’s $40 off any repair over $200. Call (888) 292-7536 for a free estimate.
Yes. We service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That includes operators, control boards, safety sensors, and intercom wiring. If your gate is a make not on that list, call anyway and describe it. There’s a good chance we can still work on it.
Yes. A live person answers the phone at any hour, and we prioritize gates stuck open or failing to lock. If your gate is jammed on a driveway at night or a safety reverse has failed, call and we’ll get you scheduled. We’d rather hear from you at 2 a.m. than have someone drive through a broken gate in the morning.
It means if the repair isn’t right, we come back and make it right within 90 days of the job. It’s in writing on every invoice, not buried in fine print. One call brings us back, no runaround and no argument. We stand behind the repair because our name is on the shop and on the invoice.
Clear the driveway and about a foot of space on both sides of the gate so we can swing it freely and lay out tools. Have the gate code or key ready if it’s on an operator. If you have a manual for your opener or any past repair receipts, have those handy too. That’s it. We bring the tools and the welding rig.
Schedule Your Gate Repair Service in Paradise Today
Whether your gate is dragging, won’t lock, or the opener’s acting up, we’d rather look at it now than wait for it to fail completely. A live person answers around the clock, the estimate is free, and the price is agreed before any work starts. Check our Gate Repair in Whitney page if you’re nearby, or call (888) 292-7536 and we’ll get your gate working right.
Gate Repair Service in Paradise – Page Notes
A few in-content resources we keep handy: our Gate Repair in Paradise page covers the full scope of what we repair in this area. For installation and operator service, our home page and nearby Winchester page round out what we handle.
Written by the team at Gatewood Fence & Gate.