Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterElectric Gate Repair Costs in Paradise, NV: What the Price Guides Get Wrong
Electric gate repair in Paradise typically runs $60 to $500, and the biggest factor in what you pay isn’t the motor – it’s whether the technician diagnoses the electrical chain correctly before quoting. Most “gate motor replacement” bills we see on the east side of the Strip were actually failed sensor wiring or a sun-cracked low-voltage run, not a dead operator. If you’re staring at a gate that won’t move and wondering what the damage will be, call (888) 292-7536 for a free estimate. Hal Gatewood answers, day or night.
Why Desert Heat Chews Up Your Gate’s Wiring First
In a climate that pushes past 115°F in July, the wire running from your control box out to your safety sensor can go brittle and crack in as little as three years. UV does the damage on any exposed run, and Paradise has thousands of gates with low-voltage wire baking in full sun because nobody buried it deep or sleeved it. Here’s the failure sequence we see over and over on Paradise gates:
- UV degrades the wire insulation on exposed runs along fences and gates facing west or south.
- Sensor wires short or open up – the gate either won’t move at all, or it moves without a working safety cutoff, which is the dangerous version.
- Monsoon grit packs the photocell lenses after a dust storm. The beam can’t get through, the gate reads “obstruction,” and it refuses to close.
- A tech who only sees “gate not working” recommends a motor or board, and you spend $400 on something that was never broken.
That last part is the reason this page exists. The two failures above are cheap to fix – usually $60 to $150 – but they get misdiagnosed as operator or board failures constantly. Show us a gate closing on its own and we’ll show you where the sensing circuit is actually failing. Same with a gate that won’t respond at all: nine times out of ten the control box is fine and the wiring between it and the sensor is the problem.
Electric Gate Repair Cost Breakdown by Component
Because the electrical side of a gate is where the real money question lives, here’s how the numbers break out for a residential 110V system in Paradise. These are the ranges we quote, stated upfront on the estimate. The $40 off any repair over $200 applies to electrical repairs too – no haggling required, it comes off the quote.
| Repair / Component | Typical Cost Range |
|---|---|
| Safety sensor / photocell replacement | $60 - $120 |
| Low-voltage wire re-run | $80 - $180 |
| Logic / control board replacement | $90 - $250 |
| Full operator electrical rebuild | $300 - $500 |
| Mechanical repair (hinges, arms, rollers) for comparison | $120 - $350 |
Notice the contrast: a sensor or wiring re-run is a fraction of what a full operator rebuild costs, and it’s the failure you’re most likely to have. That’s why diagnosis comes first. The name is on the shop, and the shop is down the road – we’d rather find the cheap fix than sell you a motor. Every job carries the 90-Day Done Right Promise in writing, so if it comes back, so do we.
When the Gate Is Commercial, the Numbers Change
Paradise isn’t a master-planned suburb. It’s a built-up unincorporated strip where casino service entrances, resort gates, and mid-century motel iron sit on the same block as single-family driveways. Commercial electric gates on those resort and casino-adjacent properties often run on three-phase power or higher-voltage commercial circuits, and that changes two things: the repair cost is different, and the licensing required to work on it is different. Not every gate company in the valley is set up for commercial electrical work.
On the residential side, the housing stock tells its own story – 1960s to 1980s homes, low-rise apartments, and motel-era properties with original wrought-iron or chain-link driveway and pool gates. Those gates have been baked and bent by desert sun for decades. Pool gates in particular have to satisfy Nevada’s child-safety self-closing and self-latching code, so a call about a pool gate often means both re-welding heat-fatigued iron and re-setting a safety hinge for code. That’s on-site welding work, not a haul-away-and-replace job.
For the full picture of what we handle beyond electric operators, see our Gate Repair page. For everything we do in town, start at our home page.
What a Proper Electrical Diagnosis Looks Like
Hal works repair-first. Before anyone recommends a new operator, these get checked in order:
- Power at the control box. Confirm the supply is live and the transformer is delivering what the board expects.
- Sensor circuit continuity. Test the low-voltage run end to end – this is where cracked, sun-brittle wire shows up.
- Photocell beam and lens condition. Clear monsoon grit and verify the beam actually lands.
- Control board diagnostics. Read the fault codes and confirm the board is failing, not just reporting a downstream problem.
- Mechanical load. Check hinges, arms, and rollers so a binding gate isn’t blamed on the electrical side.
He’s certified to service LiftMaster, FAAC, Elite, and Mighty Mule operators, among others, so the diagnosis matches the equipment. Fix the panel without the post and you’ll fix it twice – same goes for replacing a board without checking the wire feeding it.
A word on safety. Gate operators run on live line voltage, and commercial systems run higher. We don’t publish do-it-yourself steps for the electrical side because opening an operator enclosure or working near a live circuit without training can seriously injure you. That’s a job for a trained professional, and it’s why we keep the truck stocked and come to you. If your gate is stuck open or running without its safety cutoff, treat it as a safety problem, not a convenience one.
Why a Live Answer at 2 A.M. Actually Matters
An electric gate failure at night is a security event. A gate stuck open on a motel-era property or a resort service entrance leaves the lot exposed until morning, and that’s not something you want to leave on a voicemail. Calls here get answered by a live person 24/7 – not a recording, not a queue three states away. You tell us what’s happening, we tell you what it’s likely to cost and when we can be there.
Standing offers, no haggling: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Our technicians have up to 25 years of experience, and they’re background-checked.
FAQs
Most electric gate repairs in Paradise run $60 to $500, depending on the component. Sensor and photocell replacement is typically $60-$120, low-voltage wire re-runs are $80-$180, control board replacement is $90-$250, and a full operator electrical rebuild is $300-$500. Call (888) 292-7536 for an exact quote – estimates are free.
It’s more often the wiring or a sensor than the motor. In Paradise’s heat, exposed low-voltage wire cracks within a few years, and monsoon grit packs the photocells; both fail far more often than the operator itself. A proper diagnosis before any replacement is what keeps the bill down. Call (888) 292-7536 and we’ll check the cheap culprits first.
In most cases, yes – same-day service is available, and our line is answered by a live person 24/7 for after-hours emergencies like a gate stuck open. A free estimate is standard, with pricing stated upfront before any work starts. Call (888) 292-7536.
Yes. Commercial gates on resort, casino-adjacent, and multi-unit properties often run on three-phase or higher-voltage circuits, and we’re set up for that work – including the different licensing it requires. Tell us the setup when you call and we’ll confirm before we come out. Reach us at (888) 292-7536.
Get a Straight Price Before You Approve Anything
If your gate is down and the last quote felt like a guess, get a second look. Free estimate, upfront pricing, and a real person on the phone – (888) 292-7536. We’ll diagnose the electrical chain before anyone recommends a motor, and the 90-Day Done Right Promise goes on the job in writing. Call Gatewood Fence & Gate Paradise today.
Written by the team at Gatewood Fence & Gate Paradise, serving Paradise, NV.
What Our Customers Say
"Safety photo eyes on our old gate had been bypassed by whoever serviced it last, which he was genuinely annoyed about on my behalf. Fitted proper sealed ones and wired them the way they should be."
- Otis Redmond"Welded the hinge back onto our wrought iron gate on site rather than taking it away for a fortnight. Ground it back and painted it and you cannot see the repair."
- Winston Achterberg"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth