Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Las Vegas
A sagging driveway gate, a hinge that pulls loose from the block wall, a welder who never shows: these are the calls we get from Las Vegas homeowners every week. We’re Gatewood Fence & Gate Paradise, and gate parts and welding is what we do, whether it’s a hinge replacement in a 1990s stucco tract home or custom welding on an ornamental steel leaf that the sun has been baking for two decades. We know the valley’s block walls, sun-baked finishes, and wind-whipped side yards because this is where we work. Call (888) 292-7536 and a live person picks up, day or night, with a free estimate on the spot.

Why Gatewood Fence & Gate Paradise Is Las Vegas’s Preferred Gate Parts & Welding Company
Las Vegas homeowners call us because they’ve already been through the other kind of outfit: the one that quotes a number over the phone and charges a different one at the door. We quote and agree on the price before any work starts. Every job carries our 90-Day Done Right Promise in writing, and if something isn’t right, one call brings us back, no runaround.
Our technicians have up to 25 years of experience with the gates and operators that fill Las Vegas neighborhoods, and we’re certified to service nine major brands, from LiftMaster openers to DoorKing access hardware. We’re a repair-first shop: if a hinge replacement and a weld will get another ten years out of a gate, that’s what you get, not a sales pitch for a whole new gate. We don’t carry parts in a truck or run out of a warehouse, because the local pro who arrives brings what the job actually needs, and we tell you what’s available up front.
Calls are answered by a live person around the clock, not a voicemail or a call center three states away. When you describe a dragging gate over the phone, you’re talking to someone who can picture it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Las Vegas
Hinge Replacement in Las Vegas
Most gate hinge failures in Las Vegas start in the post, not the hinge plate. UV-hardened pivot bushings and a footing that has lost its alignment lock the hinge up, and the hinge then yanks the block anchor loose. We replace hinges, re-shim block anchors, and weld reinforcement plates so the fix holds through the next monsoon season.

Post Replacement in Las Vegas
When the hinge post itself is compromised, welding plates onto it just makes you fix the same gate twice. We cut out the failed post and set a new one, aligning it to how the wall actually sits, which in northwest valley subdivisions on shared CMU block walls is rarely where it was at install. If the post is sound and only the hardware has drifted, we say so.

Rail Repair in Las Vegas
Monsoon microbursts and dust-storm gusts twist unsupported gate leaves, bending rails and pulling anchors out of block walls. We straighten and re-weld bent rails on site in your driveway rather than hauling the gate off, so you’re not looking at an open gap in the fence for a week.

Custom Welding in Las Vegas
We weld in the driveway, not in a shop across the valley. Ornamental steel leaves that are still structurally sound but need repaired welds, new brackets, or reinforcement plates get welded on site. When a gate is beyond welding, we’ll tell you plainly that replacement is the cheaper answer, and quote it before anything is ordered.
Latch and lock repair and gate roller replacement fall under the same Gate Parts & Welding work, and we can combine them into one visit.
Trusted Brands We Service in Las Vegas
We’re certified to service nine major gate brands, including LiftMaster operators, Elite slide and swing operators, and Mighty Mule residential systems. In Las Vegas, the most common failure we see in older operators is an obsolete control board that has cooked in a 110°F+ summer and now operrates erratically or not at all; sometimes it isn’t made anymore. We tell you honestly what’s replaceable and what isn’t, and quote the fix before we start.

Common Gate Parts & Welding Problems We See in Las Vegas Homes
- UV-baked powder-coat. Years of desert sun break down the finish on ornamental steel gates, and the rust that follows binds hinges and latches. West-facing gates in Las Vegas are hit hardest.
- Monsoon-racked leaves. A microburst gust racks an unsupported gate leaf, bending rails and pulling anchors loose from a shared block wall. It’s often a wall-anchor job as much as a gate job.
- Obsolete control boards. Older LiftMaster and FAAC operators fail from heat and dust, and the board that runs them is often no longer available, leaving you deciding between retrofit and a new operator.
- Wandering posts. In northwest Las Vegas neighborhoods, gates hung on shared CMU block walls settle independently from the house slab, so a gate that was square at install goes out of plumb within a few summers.
Why Desert Heat and Block Walls Change the Repair in Las Vegas
Las Vegas gate trouble is a sun and wind story, not a rain and rust story. The extreme dry heat warps steel and wood, bakes the finish off, and hardens the grease in pivot bushings until a gate starts dragging. In the northwest valley, a lot of driveway gates are hung on shared CMU block walls that settle at a different rate than the house slab. That’s why so many gates go out of plumb after a few summers and need re-shimming at the block anchors, not just a hinge turn. A typical call is a fifteen-year-old swing gate in an HOA subdivision that drags because the hinge post shifted in the block wall. The usual cause is UV-hardened bushings and a footing that lost its alignment, and a qualified local pro will re-shim the anchors and replace worn hinges. If the post itself is compromised, replacement is often the cheaper long-term answer.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Parts & Welding in Las Vegas, NV
We quote and agree on the price before any work starts, so the number you hear is the number you pay. A typical hinge replacement in Las Vegas runs $150 – $350 per leaf, and re-shimming block-wall anchors while we’re there adds $75 – $200. Post replacement runs $400 – $900 depending on the post and how it’s set into CMU block. Rail straightening and re-weld work runs $200 – $500, and custom welding on site runs $125 – $250 per hour with a one-hour minimum. What moves the price is the material, how far off-plumb the gate is, and whether the repair turns into a wall-anchor job. Written estimates are free, and we’ll give you a second opinion on any other estimate at no charge.
We Also Serve Cities Near Las Vegas
We work the whole valley, not just Las Vegas proper. That includes Las Vegas neighborhoods and the surrounding communities of Winchester, North Las Vegas, Sunrise Manor, and Paradise, plus the ZIP areas 89165, 89166, 89162, and 89111. If you’re just outside one of these, call and ask, we’ll tell you straight.
Serving Las Vegas, NV – Our Local Coverage Area
We serve Las Vegas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Las Vegas
Replacing only the hinges usually won’t fix a gate whose hinge post is loose. When the post has shifted in the block wall, new hinges bolt onto a post that’s still out of line, and the gate drags again within a season. The right fix re-shims the block anchors and addresses the post before the hinges. Call (888) 292-7536 for a free look and a written price.
If the control board isn’t made anymore, you have two honest choices: retrofit the operator with a modern board and safety package, or replace the operator. Heat and dust in Las Vegas are hard on older boards, and a 15-to-20-year-old operator that’s already past its board is usually cheaper to replace than to keep patching. We’ll tell you which way the math leans before you commit.
Because the shared CMU block wall settles at a different rate than the house slab it’s built beside. A gate that was square at install drifts out of plumb over a few summers as the desert soil shifts and the block anchors loosen. Re-shimming at the block anchors, not just turning the hinges, is what realigns it.
If the gate leaf, welds, and posts are sound, repair is almost always cheaper. Once the posts are compromised and the operator’s control board is obsolete, replacement often wins on total cost. We price both so you can compare them side by side. Call for a free estimate with numbers written down.
Automatic gates need safety devices that sense an obstruction and stop or reverse, typically photo-eye sensors and an edge sensor, along with proper warning signage. Local code follows the safety standard for automated vehicular gates, and older gates hung before those requirements often don’t have them. We check yours and tell you what’s missing before we touch the operator.
Get a Free Gate Parts & Welding Estimate in Las Vegas
If your gate is dragging, a hinge is pulling loose, or a weld has given out, call (888) 292-7536 for a free estimate. A live person answers around the clock, we quote and agree on the price before any work starts, and every job carries the 90-Day Done Right Promise in writing. We repair what other shops want to replace, and we weld on site so your gate stays in your driveway. Seniors and veterans get a permanent 10% discount, and there’s no trip charge inside the county.
Written by the team at Gatewood Fence & Gate Paradise.