A Gatewood company - serving Paradise, NV

Before & After Gallery - Gatewood Fence & Gate Paradise

Wood & steel frameWood & steel frame
Wrought ironWrought iron
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Paradise, NV

A gate that won’t close tells you more in five seconds than any brochure can. On this page we show the kind of work we do around Paradise: the sag, the drag, the motor that quits, the hinge that’s pulling out of the post. Photos get added here as jobs come in, so what you see reflects what we actually fix.

Call (888) 292-7536

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Recent Transformations

Hinged Driveway Gate That Sagged and Scraped the Ground

BeforeBeforeAfterAfter
Before & after – hinged driveway gate realignment and hinge post repair, Paradise, NV

The gate was dragging on the driveway and you had to lift it to close it. The problem wasn’t the gate frame at all. A gate sags in the hinge post, not in the middle, and that’s where we start. The post had shifted in the soil and the top hinge had wallowed out. We reset the post, welded new hinge plates, and re-hung the gate so it swings clean. It now closes on its own weight with a light push and sits level at the latch.

Sliding Gate Motor That Ran but Wouldn’t Move the Gate

BeforeBeforeAfterAfter
Before & after – sliding gate motor service and track repair, Paradise, NV

The motor hummed, the gate didn’t budge, and the homeowner had been opening it by hand for two weeks. We found a worn drive sprocket and a track full of grit and bent rollers. We cleared and straightened the track, replaced the sprocket, and set the limits on the LiftMaster operator. The gate now opens and closes smoothly on the remote and stops where it should on the safety edges.

Wrought-Iron Gate with a Broken Weld at the Frame Corner

BeforeBeforeAfterAfter
Before & after – on-site welding repair of a wrought-iron gate frame, Paradise, NV

A cracked weld at the bottom corner let the gate rack out of square, and the latch wouldn’t line up. Fix the panel without the post and you’ll fix it twice, so we checked the post first, then welded the corner on site in the driveway. No hauling it off, no waiting on a shop. The gate squared up, the latch caught, and the frame is solid again.

Automatic Gate Opener That Reversed for No Reason

Technician performing professional metal gate hinge repair and maintenance
Before & after – gate opener safety edge and control board repair, Paradise, NV

The gate would start to close, then reverse halfway every time. That’s usually a safety device doing its job, or a control board misreading it. We traced it to a failing safety edge and a control board that had taken on moisture. We replaced the edge, dried and reseated the board, and tested the reverse cycle by hand. The gate now closes fully and stops on contact like it’s supposed to.

Double Swing Gate Where the Post Had Pulled Loose

Professional welder performing onsite gate repair services on a metal driveway gate.
Before & after – double swing gate hinge post reset and re-hang, Paradise, NV

One leaf of a double gate was leaning and the gap at the center latch had opened to a few inches. The hinge post had heaved and the gate was pulling away from it. We dug out the post, reset it in fresh concrete, and re-hung both leaves off the repaired post. The two leaves meet at the center again and the gate swings true.

Old Iron Gate Restored Instead of Replaced

Professional repairing a crack on a metal gate post cap.
Before & after – iron gate restoration, hinge replacement and re-weld, Paradise, NV

Rust had eaten through two hinges and the gate was hanging by a thread. The homeowner expected to replace the whole thing. We welded in new hinge barrels, cleaned and treated the rusted joints, and re-hung the gate on the original posts. It opens and closes like new, and it’s the same gate that was there before.

Want Results Like These?

If your gate is sagging, stuck, or making a noise it didn’t used to make, call Gatewood Fence & Gate at (888) 292-7536. We repair first, weld on site, and price the job upfront before any work starts. $40 off any repair over $200, and no trip charge inside the county. Estimates are free.

Written by the team at Gatewood Fence & Gate.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need Gate Repair help in Paradise? Licensed & insured · 30-60 min response · free estimates
Call (888) 292-7536
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Gatewood Fence & Gate Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch