Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Hinge & Roller Replacement: The Paradise Owner’s Guide
DoorKing hinge and roller replacement typically runs $145 to $280 per gate leaf, installed, here in Paradise, and we can usually get out same-day when you call before mid-afternoon. The local pro is licensed and insured as Nevada requires, and every price gets quoted and agreed before a wrench turns. Most Paradise owners don’t wake up thinking about hinges. What they notice is a gate that clangs ten feet too far, a bottom roller dragging a curb stripe into the driveway, or a hinge post that has started to lean a half-inch a year. In older Paradise neighborhoods, the roadside gates tend to sit right in that sun-baked afternoon line, and it’s the small parts that give out first, not the operator.
Which DoorKing Models This Applies To
DoorKing hinge and roller hardware shows up across the 6400, 6500, 6600, and older 6300 series swing operators, plus the slide and cantilever lines that use a roller carrier underneath the gate leaf. The hinge plate pattern changed on some mid-2000s units, so the same replacement hinge that fits a 2009 6400 will not bolt onto an earlier 6300 without a different bracket. That’s the gotcha you need to catch.
To match the right part, read the data plate inside the operator housing (it gives the model number and serial), then measure the hinge pin diameter and the distance between mounting holes on the existing plate. A pin that measures 5/8-inch versus 3/4-inch is a whole different part. DoorKing OEM hinges and rollers are the safest fit, and they tend to hold up well under constant cycling. There are quality aftermarket rollers with sealed bearings that many shops carry, and they run a bit cheaper, but the hinge plates themselves are best kept OEM for exact bolt pattern and metal thickness. We’re an independent service provider, not affiliated with DoorKing, so we’ll happily source either OEM or a good aftermarket equivalent, whichever you prefer, and tell you the trade-off in plain terms. We do also service LiftMaster, Mighty Mule, Ghost Controls, and the rest of the nine major brands we’re certified on.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Hinge & Roller Replacement Is Failing
- Gate slams shut or swings wide on its own. Usually a worn hinge pin or a roller riding uneven, which throws the leaf off balance and makes the operator work harder to hold it.
- Visible rust streaks or red dust at the hinge. Sealed bearings break down first, then the roller seizes and the whole thing drags. In Paradise’s dry heat the grease bakes out faster than in cooler climates, so this one comes early.
- Gate binds or hesitates at one point in the swing. A collapsed roller or a bent hinge plate creates a pinch point. Not a motor problem, even if it feels like one.
- Sagging toward the hinge side. The hinge post and hinge plates carry the load. A worn hinge accelerates the sag. Fix the panel without the post and you’ll fix it twice.
- Grinding, clicking, or clunking as it rolls or swings. Metal-on-metal from a failed roller is the classic sign. Left long enough, it starts chewing the track or the gate frame too.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Figure $145 to $280 per gate leaf for hinge and roller replacement in Paradise, installed. The low end covers a straightforward swap on one hinge or a single roller carrier. The high end covers multiple hinges plus rollers, or a hinge plate that needs a bracket change.
| Item | Typical Range |
|---|---|
| Single hinge replacement | $65 – $120 per hinge |
| Roller or roller carrier | $55 – $110 each |
| Full set (both leaves, hinges + rollers) | $220 – $420 |
| Hinge post repair if sagging | quoted separately after inspection |
That’s the part plus the labor to fit and adjust it. We quote and agree the price before any work starts, so the number on your invoice is the number we said out loud. Every job carries our 90-Day Done Right Promise in writing, and there’s a $40 discount on any repair over $200, no trip charge inside the county, plus a permanent 10% off for seniors and veterans.
DIY or Call Us?
You can safely look at the problem and take a couple of photos. Read the data plate inside the operator, measure the hinge pin, and note whether the gate sags toward the hinge side or binds in the swing. That’s a five-minute check and it saves a return trip.
What I’d steer you away from is pulling a hinge plate off a gate that’s still hanging on it, especially on a heavier steel leaf. The gate can come down on you, the closer or operator can snap the leaf shut the wrong way, and you can crack a post trying to force a pin. Springs and operators need trained hands, full stop. Hinge work is safer but still load-bearing, and a wrong bracket choice will let the gate walk off its post. For anything that’s already sagging or binding, call us at (888) 292-7536. Estimates are free, and I stand behind the diagnosis.
FAQs
How long do DoorKing hinges and rollers last in Paradise? A well-maintained DoorKing roller carrier generally lasts 5 to 10 years, and hinge plates often run longer, but our dry heat and sun exposure bake grease out faster than cooler climates. Kept greased and adjusted, they’ll reach the high end. Neglected, rollers can seize in three or four years.
Can the hinge or roller be repaired instead of replaced? Sometimes, yes. A roller with a good bearing can often be re-greased and reset, and a hinge plate can sometimes be tightened and re-aligned. If the metal is cracked, the sealed bearing is dead, or the pin is worn oval, replacement is the honest answer. Call (888) 292-7536 for a free second opinion if you’ve got a written estimate that says replace.
How long does a hinge and roller swap take? Usually an hour or two per gate leaf, depending on how stuck the old hardware is and whether the post needs attention. We’ll tell you the time when we quote, and you’ll know before we start.
How do you source the DoorKing part for my gate? From your model number and serial off the data plate, plus measurements off the existing hardware, we order the exact OEM hinge or roller, or a quality aftermarket equivalent if you’d rather. When it arrives, the same or next business day, we fit it and test the full swing before we leave. Call (888) 292-7536 to get the part matched and a written price in hand.
Written by the team at Gatewood Fence & Gate Paradise, serving Paradise and nearby areas.
Call (888) 292-7536 for a free estimate. A live person answers any hour, and we’ll get out there, confirm the exact part, and quote it before we touch a thing.