A Gatewood company - serving Paradise, NV

DoorKing Gate Parts & Welding in Paradise, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

DoorKing Gate Parts & Welding in Paradise: What to Know First

We repair and weld DoorKing gates in Paradise as an independent DoorKing service provider, and most hinge, post, and rail jobs are finished on-site the same day. Parts that need ordering (operator gears, control boards, loop detectors) usually land within a few days, and the price for a repair is always agreed with you in writing before anyone lifts a wrench. This page is for DoorKing owners in Paradise whose gate is sagging, dragging, squealing, or simply not latching anymore – the ones who want a name on the invoice, not a national outfit quoting one number on the phone and another at the door.

Call (888) 292-7536

Call (888) 292-7536 and a live person answers, day or night. Estimates are free.

How DoorKing Products Fail – and How We Fix Them

DoorKing builds tough, honest equipment, but every design has a weak spot, and in Paradise the desert heat and dry air find those weak spots faster than most. Here are the failures we see most often on DoorKing gates around town.

  • Hinge-post rot and lean on 6000-series swing gates. A gate sags at the hinge post, not in the middle of the panel – that’s where we start. DoorKing’s 6000-series arms are heavy, and the post that anchors them takes years of torque. In Paradise the sun bakes the paint off the post base, moisture gets in, and the metal gives way. We weld a new plate or post cap, or reset the post, and the gate swings true again.
  • Rail cracking at the weld seams on older 1601 and 1602 gates. The seam where the horizontal rail meets the upright is the highest-stress point on any welded gate. DoorKing builds to a good spec, but a gate that’s been hit, or just pushed on for years, cracks there. We cut out the old weld, prep the joint properly, and lay a fresh bead on-site – the gate never leaves your driveway.
  • Roller and track wear on sliding models. DoorKing slide gates ride on rollers that flatten out and track that bends. A dragging slide gate is usually a roller that’s worn to the axle, not a motor problem. We replace the rollers, true the track, and re-check the operator before we call it done.
  • Latch and lock alignment drift. The latch grabs the keeper cleanly for a while, then the post settles a quarter inch and suddenly the gate won’t close. That’s alignment, not a bad latch. We re-hang and adjust the arm so the latch meets dead-on, and we weld the keeper back where it belongs.
  • Custom welding and gate armor. Some gates just need a proper repair – a bent picket, a torn corner, a section that’s been kicked in. We cut, fit, and weld on-site so the gate matches what’s already there instead of getting swapped for a new one. Fix the panel without the post and you’ll fix it twice, so we look at the whole assembly.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our DoorKing Gate Parts & Welding Process

Here’s how a DoorKing job actually runs when you call us in Paradise:

  1. 1
    Pick up the phone. A live person answers, 24/7. Tell us the model if you know it, or just describe what the gate is doing. We’ll walk you through a couple of quick checks so we show up with the right parts.
  2. 2
    Diagnose on-site. We look at the gate, the post, the operator, and the track – not just the part that’s acting up. Show us the gate closing on its own and we’ll show you where it’s failing.
  3. 3
    Parts decision. DoorKing OEM parts when the model calls for it, quality aftermarket where the OEM piece is overpriced for the job. We tell you which is which and why, and you approve it before we order anything.
  4. 4
    Repair and weld. On-site welding, on the gate, in your driveway. The panel gets fixed and the post gets checked – every time.
  5. 5
    Test and walk it with you. We run the gate open and closed, test the latch, check the operator, and walk the whole thing through with you before we pack up.
  6. 6
    Clean up and guarantee it in writing. The 90-Day Done Right Promise goes on every job. If it’s not right, one call brings us back.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What DoorKing Gate Parts & Welding Costs in Paradise

Prices in Paradise run a little higher than the valley average because of travel and the desert repair cycle – sun-baked posts and worn rollers come up faster here. Here’s what we typically quote:

Job Typical range
Hinge replacement (per hinge, welded) $150 – $275
Hinge-post replacement or reset $350 – $650
Rail repair / on-site weld of a cracked seam $175 – $400
Gate roller replacement (set) $120 – $250
Latch and lock alignment repair $95 – $200
DoorKing OEM operator part (gear, board, detector) $200 – $900+, depending on the model

What moves the price: how much welding is needed, whether the post has to be pulled and reset, OEM versus aftermarket parts, and access. Nothing starts until you’ve seen the number and agreed to it. Ask about $40 off any repair over $200, no trip charge inside the county, and a free second opinion on any written estimate. Seniors and veterans get a permanent 10% discount.

Why Paradise Homeowners Call Gatewood Fence & Gate Paradise for DoorKing Work

We’ve been locally owned and owner-operated since 2001, and the name is on the shop and on every invoice – that’s the oldest accountability there is. A live person answers the phone around the clock, not a voicemail and not a call center three states away. The person who shows up has been fixing gates since 2001 and knows DoorKing’s failure points cold. Every job carries the 90-Day Done Right Promise in writing, and if something isn’t right, one call brings him back.

We also service LiftMaster, Mighty Mule, and Ghost Controls, so if your DoorKing shares a driveway with one of those, we can handle both. The name is on the shop, and the shop is down the road.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (888) 292-7536
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Gatewood Fence & Gate Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch