Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Paradise Owner’s Guide
We replace Ghost Controls gate motors in Paradise with a tested motor, matched to your operator’s model and arm type, and the installed price usually lands between $550 and $900 depending on the model and what has to be re-cut, re-welded or re-mounted. Most gate motor replacements we do in Paradise are finished in a single visit. A failed gate motor rarely dies without a warning. In our experience it starts as a gate that hesitates a few inches off the latch, then groans, then reverses halfway, until one morning the remote clicks and nothing moves at all. Homeowners in Paradise tend to call when the gate stops closing all the way on its own – that is usually the motor straining against a hinge that has started to sag, not the motor giving up on its own.
Key takeaways
- Ghost Controls motor replacements in Paradise typically run $550 – $900 installed, parts and labor quoted together before we start.
- We service Ghost Controls across its full residential line, and we will not swap a motor that only needs the arm or the board.
- Every motor replacement carries our 90-Day Done Right Promise in writing.
- We are an independent service provider, not affiliated with Ghost Controls.
Which Ghost Controls Models This Applies To
Ghost Controls makes residential swing gate operators, and the models you’ll see on gates in Paradise fall into a few families: single-arm and dual-arm kits, the Titan and heavier-duty lines for longer or wider gates, and the lighter-weight Stealth and Legacy units for standard driveway gates. The part that actually fails determines what we replace – often it’s the actuator arm, sometimes the control board, sometimes the whole operator housing when the motor itself has burnt out.
To identify the right part, we look at the model label on the rear of the control box, the arm’s stroke length, and whether the gate is a single or double swing. That label matters more than anything else on the page. A Stealth arm and a Titan arm are not interchangeable, and a dual-gate system needs two matched operators or the board fights itself. On the OEM-versus-aftermarket question: for Ghost Controls specifically we lean toward genuine or factory-equivalent parts because the arm gearing and board firmware are matched, and a mismatched arm is what causes the control board to throw faults after a swap. Quality aftermarket arms exist and we’ll use them when the price gap justifies it, but we tell you which is which before we order anything.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing
- The gate opens but won’t close, or reverses mid-travel. That’s usually a limit switch or safety sensor problem before it’s a motor problem. In Paradise we see it most on gates that face the afternoon sun, where the board gets hot and the limits drift.
- The arm moves but the gate doesn’t. The motor is turning and the arm has stripped its internal gearing or the pivot pin has broken free. The motor may still be fine; the arm is what needs replacing.
- A grinding or clunking noise when the gate starts. Worn gear teeth inside the actuator. Once the teeth round off, no amount of adjusting will quiet it, and the arm will eventually jam.
- The gate moves slowly or stalls partway. The motor is straining against resistance – a sagging hinge, a dragging wheel, or a worn arm bushing. The motor is responding to a load it should not be carrying, and if it keeps straining it will burn out.
- The remote clicks but nothing happens, or the gate runs the wrong direction. A board or wiring fault, not the motor. Replacing the motor on this symptom wastes money – the board, the battery in the remote, or a corroded connection is the real cause.
Replacement Cost & What’s Included
In Paradise, a Ghost Controls gate motor replacement runs about $550 – $900 installed for a standard single-arm residential operator, and higher for dual-arm or heavier-duty lines. The range is driven by model, gate weight and width, whether the mounting post needs re-welding, and whether existing wiring and safety edges can be reused. What’s included in our quote: the motor, the arm, the mounting hardware, the wiring reconnection, adjustment of the limits, and a test of the safety reverse. Labor is not an afterthought line item – it’s in the price we give you before we start, and the price does not change at the door.
Every motor replacement carries our 90-Day Done Right Promise, stated plainly, not buried. If the setup isn’t right after we leave, one call brings us back. We also offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a standing 10% discount for seniors and veterans.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself: the model label on the control box, whether the gate swings freely by hand, whether the arm is loose at the pivot, and whether the remote’s battery is good. That tells you whether the motor, arm or board is the likely culprit, and it’s worth five minutes.
Where DIY goes wrong is at the electrical and mechanical connection point. Swapping a motor means working live low-voltage wiring at the board, setting the limits so the gate doesn’t over-travel and break the arm, and matching the new arm to your existing gate hardware. If a hinge is sagging or a post is loose, the new motor will fail the same way the old one did – fix the panel without the post and you’ll fix it twice. We’d rather you call us before you spend money on a part that turns out to be the wrong one. Call (888) 292-7536 for a free estimate, or to talk through what you’re seeing on the gate.
FAQs
Most Ghost Controls residential arms last 8 to 12 years in our experience, but Paradise heat and sun exposure shorten that on gates facing west or south. Regular hinge and limit adjustments get you to the upper end of that range; neglected gates burn motors out in half the time.
Sometimes, yes. If the arm gearing is intact and the motor is turning, the problem is often the board, the limits, or the wiring, and repair is the right call. We always check the repair path first and only recommend replacement when the motor or arm is genuinely worn out.
A standard single-arm replacement usually takes two to three hours from arrival to a working gate, assuming the mounting post and wiring are sound. If the post needs welding or the wiring has been damaged, plan on a longer visit.
We match the exact model and arm to your operator, then order the correct part from our supply partners. We tell you whether it’s a genuine Ghost Controls part or a factory-equivalent before we order, and we don’t carry parts on a truck or claim stock we don’t have.
Call Gatewood Fence & Gate Paradise
If your Ghost Controls gate is straining, grinding, or refusing to close, call (888) 292-7536 for a free estimate. We’re locally owned and owner-operated, a live person answers every call 24 hours a day, seven days a week, and we service Ghost Controls alongside LiftMaster, Mighty Mule, and DoorKing. We’ll tell you honestly whether the motor needs replacing or something smaller does, we’ll quote the work before it starts, and we stand behind it in writing. That’s how we’ve worked in Paradise and the surrounding communities for over 29 years.
Written by the team at Gatewood Fence & Gate Paradise, serving Paradise and nearby areas.