A Gatewood company - serving Paradise, NV

LiftMaster Gate Motor Replacement in Paradise, NV

LiftMaster operatorsLiftMaster operators
Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

LiftMaster Gate Motor Replacement: The Paradise Owner’s Guide

We replace LiftMaster gate motors in Paradise, and most installed jobs land between $650 and $1,450 depending on the model and whether the arm, operator, and control board get swapped together. If your gate has quit in the middle of the driveway, we can often get eyes on it the same day. Most Paradise owners find out the motor is done the same way: the gate stops halfway, reverses on its own, or just hums and clicks when you hit the remote. Then the arm starts leaking oil, or the thing runs a few feet and gives up. That’s usually the moment we get the call.

Call (888) 292-7536

Which LiftMaster Models This Applies To

LiftMaster swing and slide operators are what we see most in Paradise, and the model number matters because the mount pattern, arm length, and control board generation all change between families. The common residential lines are the CSL24U slide operator, the LA400 and LA500 swing arms, and the older Elite and SL-series units that are still running on plenty of Paradise properties. Find your data plate on the operator housing (or on the arm on swing models) and note the exact model and the voltage. That plate is what we match the replacement against, and on older units the revision letter matters because the factory changed the control board pinout mid-production. We are an independent service provider and not affiliated with LiftMaster; we work on their equipment and match the right OEM or quality aftermarket equivalent to your specific model. We also service Mighty Mule, Ghost Controls, and DoorKing.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your LiftMaster Gate Motor Replacement Is Failing

When a LiftMaster motor starts to go, it tells you first. Here’s what Paradise owners report, and what’s usually underneath it:

  • Gate stops or reverses halfway. The control board is losing the limit position, or the motor windings are drawing too much current and the board trips on overload.
  • Motor hums or clicks but the arm doesn’t move. The gear train or the capacitor has failed, and on older units it’s often the plastic drive gear stripping out.
  • Arm leaking oil or grease. The gearbox seal is gone. On a LiftMaster swing arm, that leak is usually the first sign the whole operator is near the end of its service life.
  • Gate moves slow or labors under its own weight. The motor is weak, or the gate has a binding hinge pulling against it. We check both, because a weak motor on a binding gate fails fast.
  • Remote works, keypad or loop doesn’t. The receiver or control board input has failed, which sometimes means a board swap instead of a full motor replacement.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed LiftMaster gate motor replacement in Paradise runs $650 to $1,450. The low end covers a straight single-swing operator swap with the existing control board reused. The high end covers a slide operator, new arm, control board, and safety edges, plus whatever wiring needs to be cleaned up. The range moves with model, gate weight, and whether the old mount pattern lines up with the new unit. You get a written quote before we start, and it doesn’t change at the door. Every job carries the 90-Day Done Right Promise in writing: if it’s not done right, we make it right. Our technicians have up to 25 years of experience.

DIY or Call Us?

You can safely check a few things yourself: confirm the model plate, test the manual release, look for oil under the arm, and make sure the gate swings free by hand. What you shouldn’t do is open the operator housing, poke at the control board, or wire a replacement motor into live 120-volt power. LiftMaster operators run on line voltage, and the control board holds a charge even after you cut the breaker. On a swing gate the arm is under spring or gravity load, and releasing it wrong can slam the gate. That’s the part that hurts people. If you’re not sure, call us at (888) 292-7536 and we’ll walk you through the safe checks.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (888) 292-7536
Local Service Coverage

Request a Free Estimate in Paradise

Tell us what you need - Gatewood Fence & Gate Paradise responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - 24/7 Dispatch